Langsung ke konten utama

CCNA / MCSE / CCNP Certification: Making Failure Work For You

Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're going to fail an exam.  It's happened to almost all of us, yours truly included.   What you have to keep in mind in these times is that success is not a straight line.  You've probably seen charts showing the growth of an industry or a business -- you know, the ones that go from left to right, and look kind of jagged.  The line goes up for a while, then down a bit, then up some more, then down a little.  

The key?  While every business has its setbacks, the net result is that the line goes up and progress is made.  That's how you want your certification pursuit and your career to go as well - upward!

I'm not asking you to be happy about failing an exam.  You're allowed to get mad for a few minutes, vow to never take another exam again, and be disappointed.  What you're not allowed to do is stay that way.  

If you put your books away in a fit of anger, get them out.  If you took some time off, it's time to get back to work.  Again, there's nothing wrong with being unhappy about failing an exam.  It's how you handle that failure that counts.  No inventor, executive, or entrepreneur has ever been right 100% of the time.  Learn something from your failure.   Was your study time quality study time?  Did you get some hands-on practice with the technology you're studying?  Asking yourself these questions can be tough, but it can be highly valuable in making sure you don't fail the next time.  And there must be a next time - because the one thing you cannot do is quit.

Besides, take it from someone who's been there - your temporary failure makes your eventual success that much sweeter.

Label

Label:

Komentar

Posting Komentar

Postingan populer dari blog ini

CCNP / BSCI Exam Tutorial: Route Summarization And The OSPF Null Interface

CCNP exam success, particularly on the BSCI exam, demands you understand the details of route summarization.  This skill not only requires that you have a comfort level with binary conversions, but you have to know how and where to apply route summarization with each individual protocol. You also have to know the "side effects" of route summarization.  With OSPF, there will actually be an extra interface created at the point of summarization, and this catches a lot of CCNP candidates by surprise.  Let's take a look at the null0 interface and how it relates to OSPF summarization. On R1, the following networks are redistributed into OSPF, and then summarized. interface Loopback16  ip address 16.16.16.16 255.0.0.0 interface Loopback17  ip address 17.17.17.17 255.0.0.0 interface Loopback18  ip address 18.18.18.18 255.0.0.0 interface Loopback19  ip address 19.19.19.19 255.0.0.0 R1(config)#router ospf 1 R1...
Posting Komentar
Baca selengkapnya

CCNA Certification Exam Tutorial: Cisco Switching Modes

To pass the CCNA exam and earn this important certification, you’ve got to know switching inside and out.  While you’re learning all the basic switching theory, make sure to spend some time with the one of three switching modes Cisco routers can use. Store-and-Forward is exactly what it sounds like.  The entire frame will be stored before it is forwarded.  This mode allows for the greatest amount of error checking, since a CRC (Cyclical Redundancy Check) is run against the frame before it is forwarded.  If the frame contains an error, it is discarded.  If there’s no problem with the frame, the frame is then forwarded to its proper destination. While store-and-forward does perform error checking, the delay in processing the frame while this error check is run results in higher latency than the other modes you’re about to read about.  The latency time can also vary, since not all frames are the same size. Cut-through switching copies only the d...
Posting Komentar
Baca selengkapnya

CCNP / BCMSN Exam Tutorial: VLAN Trunking Protocol (VTP)

Passing the BCMSN exam and getting one step closer to the CCNP certification means learning and noticing details that you were not presented with in your CCNA studies. (Yes, I know – you had more than enough details then, right?)   One protocol you’ve got to learn more details about is VTP, which seemed simple enough in your CCNA studies!  Part of learning the details is mastering the fundamentals, so in this tutorial we’ll review the basics of VTP. In show vtp status readouts, the "VTP Operating Mode" is set to "Server" by default.  The more familiar term for VTP Operating Mode is simply VTP Mode, and Server is the default.  It's through the usage of VTP modes that we can place limits on which switches can delete and create VLANs. In Server mode, a VTP switch can be used to create, modify, and delete VLANs.  This means that a VTP deployment has to have at least one switch in Server mode, or VLAN creation will not be possible.  Again, this i...
Posting Komentar
Baca selengkapnya